Complex BPQ32.cfg from N9LYA

N9LYA has setup a complex system using multi modes and multi ports. Using Packet 1k2 and 9k6, Hf Packet 300Baud, Robust packet, Winmor, Ardop, Pactor, Fldigi, Axip, Telnet.

http://www.n9lya.com/

;N9LYA`s BPQ system Last Edited 9/23/18 (SCS TRACKERS FW V1.7L)
LOCATOR=EM68SR
MAPCOMMENT=BPQ32 Lawrence County In Node, City of Mitchell<BR>All Stations are welcome<BR>n9lya@n9lya.#sin.in.usa.noam
PASSWORD=******
NODECALL=N9LYA-8	; Node callsign
NODEALIAS=LYANOD		; Node alias (6 characters max)
IDMSG:			; UI broadcast text from NODECALL to fixed dest ID
Node: N9LYA - OPEN-NET - APRS & BBS NETWORK NODE LYANOD/N9LYA-8 Mitchell, IN Lawrence County - MidWest HF Skipnet Hub.
***			; Denotes end of IDMSG text
BTEXT:			; UI broadcast text from BCALL to destination UNPROTO=
Node:        N9LYA-8
BBS:         N9LYA 
RMS Gateway: K9BBS-10
CHAT Server: K9BBS-14
Midwest HF Skipnet HUB
***			; Denotes end of BTEXT text
INFOMSG:		; The INFO command text follows:
Type ? for Help BPQ32_6.0.16.30 N9LYA/K9BBS
Type BBS To Access The N9LYA Full Service-BBS:
Type RMS To Access The K9BBS-10 WL2K RMS Gateway:
Type CHAT TO Access The K9BBS-14 CHAT Server:
Type DX TO Access The N9LYA-6 DX Spider Server:
***			; Denotes end of INFOMSG text
CTEXT:			; The CTEXT text follows:
Welcome to LYANOD:N9LYA-7 Network Node Server, Mitchell, Indiana
Commands:
BBS RMS CHAT DX JNOS URONOD MSYS CONNECT INFO MHEARD LISTEN (port) NODES PORTS ROUTES USERS
***			; Denotes end of CTEXT text
FULL_CTEXT=0		; 0=send CTEXT to L2 connects to NODEALIAS only
			; 1=send CTEXT to all connectees

; Network System Parameters:

OBSINIT=6		; Initial obsolescence set when a node is included
			; in a received nodes broadcast. This value is then
			; decremented by 1 every NODESINTERVAL.
OBSMIN=4		; When the obsolescence of a node falls below this
			; value that node`s information is not included in
			; a subsequent nodes broadcast.
NODESINTERVAL=20	; Nodes broadcast interval in minutes
IDINTERVAL=10		; 'IDMSG' UI broadcast interval in minutes, 0=OFF
BTINTERVAL=60		; The BTEXT broadcast interval in minutes, 0=OFF
L3TIMETOLIVE=25		; Max L3 hops
L4RETRIES=3		; Level 4 retry count
L4TIMEOUT=60		; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=2		; Level 4 delayed ack timer in seconds
L4WINDOW=4		; Level 4 window size
MAXLINKS=63		; Max level 2 links
MAXNODES=550		; Max nodes in nodes table
MAXROUTES=64		; Max adjacent nodes
MAXCIRCUITS=128		; Max L4 circuits
MINQUAL=143		; Minimum quality to add to nodes table
MAXHOPS=4		; INP3 hop limit to add to tables
MAXRTT=90		; INP3 max RTT in seconds	
  		; possible, normally about 130, depending upon other
			; table sizes.
;



; TNC default parameters:

PACLEN=236		; Max packet size (236 max for net/rom)

LINMAIL
LINCHAT

/*
PACLEN is a problem! The ideal size depends on the link(s) over which a packet
will be sent. For a session involving another node, we have no idea what is at
the far end. Ideally each node should have the capability to combine and then
refragment messages to suit each link segment - maybe when there are more BPQ
nodes about than 'other' ones, I'll do it. When the node is accessed directly,
things are a bit easier, as we know at least something about the link. So,
currently there are two PACLEN params, one here and one in the PORTS section.
This one is used to set the initial value for sessions via other nodes and for
sessions initiated from here. The other is used for incoming direct (Level 2)
sessions. In all cases the TNC PACLEN command can be used to override the
defaults.
*/

; Level 2 Parameters:

; T1 (FRACK), T2 (RESPTIME) and N2 (RETRIES) are now in the PORTS section

T3=120			; Link validation timer in seconds
IDLETIME=3600		; Idle link shutdown timer in seconds

; Configuration Options:

AUTOSAVE=1		; Saves BPQNODES.dat upon program exit
BBS=1			; 1 = BBS support included, 0 = No BBS support
NODE=1			; Include switch support
HIDENODES=1		; If set to 1, nodes beginning with a #
			; require a 'N *' command to be displayed.

; The *** LINKED command is intended for use by gateway software, and concern
; has been expressed that it could be misused. It is recommended that it be
; disabled (=N) if unneeded.

ENABLE_LINKED=A		; Controls processing of *** LINKED command
			; Y = allows unrestricted use
			; A = allows use by application program
			; N = disabled

;

;
IPGATEWAY
Adapter eth1
44ENCAP 192.168.1.17
IPADDR 44.48.0.42
IPNetmask 255.255.255.248   
IPPorts 3,5,8,9,10,11,12,13
****
;
;
;-----------------------------
; BPQAPRS

APRSDIGI
 APRSCall N9LYA-3
 StatusMsg=BPQ32 VHF-APRS/wview-WMR968-Weather Station. {linbpq}
 Symbol=_        ; Icon to display for station. Default is House if omitted
 Symset=/
 ;
 ;    Specify a Dest and Path for each port you want to use for APRS. No dest means receive only port
 ;	  Ports without an APRSPath statement will not be used by the Digi
 ;
;APRSPath 1=APRS,WIDE1-1,WIDE2-2                         
APRSPath 1=APRS,IN1-1                                      ;Per Dwight
APRSPath 2=                                                ; Receive only port
APRSPath 3=
APRSPath 4=
APRSPath 5=                      
APRSPath 6=
APRSPath 7=
APRSPath 8=
APRSPath 9=
APRSPath 10=
APRSPath 11=
APRSPath 12=APRS,WIDE1-1,WIDE2-2
APRSPath 13=
APRSPath 14=		  
APRSPath 15=
APRSPath 16=
APRSPath 17=	
APRSPath 18=APRS,WIDE1-1,WIDE2-2
APRSPath 19=

;
  BeaconInterval=30                   ; Send Beacon every 30 minute

 ;    Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
 ;    If a Digimap isn`t specified for a port, digi out on the port the packet arrived on,
 ;	  	  and send to APRS-IS (if enabled)
 ;    If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n 
 
 ;Digimap 5=5,16,             ; Packets from 5 to 16, but not APRS-IS
Digimap 1=1,           ; Packets from 1 to 1 and NO APRS-IS
 
 ;TraceCalls=WIDE,TRACE  ; Calls for CALLN-n Processing with Trace
 TraceCalls=WIDE,IN        ; Calls for CALLN-n Processing with Trace
 FloodCalls=LYA         ; Calls for CALLN-n Processing without Trace
 DigiCalls=n9lya-3       ; Calls for Normal (ie no SSID manipulation) Digi
                        ; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
						
 ReplaceDigiCalls       ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
						
 MaxTraceHops=2         ; Max value of n in CALLN-n processing. If a packet is received with n greater than
 MaxFloodHops=2         ; this, the value will be replaced BEFORE it is decremented.

; GPSPort=/dev/ttyACM0              ; if specified, lat/lon will be taken from a GPS
; GPSSpeed=9600
; GPSSetsLocator=1 

 ; You can specify a fixed LAT/LONG instead of using GPS

LAT=3844.42N           ; Must be in standard APRS Format
LON=08628.33W          ; Must be in standard APRS Format

 ;IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS

 ;ISHost=rotate.aprs.net    ; APRS-IS Host Name
 ;ISPort=14580              ; Normal port for a filtered feed
 ;ISPasscode=12418          ; If you don`t already have a passcode I can issue you one.

 ;WXFileName=/dev/shm/aprs.pkt
 WXFileName=/var/www/mitchellwx/formateddata.txt
 WXComment=/MITWXN Mitchell IN N9LYA-3 KINMITCH1 Weather Station (linBPQ)
 WXPortList=1            ; comma separated list - include IS to send to APRS-IS
 WXInterval=3            ; mins
 
***

; Port Definitions:

PORT			;144.390 APRS 1200
 PORTNUM=1
 ID=APRS 144.390 Icom2200H    	; Displayed by PORTS command
 TYPE=ASYNC		; Port is RS232 Com
 PROTOCOL=KISS		; TNC is used in KISS mode
 FULLDUP=0		; Only meaningful for KISS devices
 COMPORT=/dev/ttyUSB7              ; # = SERIAL COM PORT 
 SPEED=38400		; RS232 COM PORT SPEED
 CHANNEL=A		; A for single channel TNC, A or B for multichannel
 PERSIST=230		; PERSIST=256/(# of transmitters-1)
 SLOTTIME=100		; CMSA interval timer in milliseconds
 TXDELAY=350		; Transmit keyup delay in milliseconds
 TXTAIL=0		; TX key down, in milliseconds, at packet end
 QUALITY=0		; Quality factor applied to node broadcasts heard on
			; this port, unless overridden by a locked route
			; entry. Setting to 0 stops node broadcasts
 MINQUAL=95		; Entries in the nodes table with qualities greater or
			; equal to MINQUAL will be sent on this port. A value
			; of 0 sends everything.
 MAXFRAME=2		; Max outstanding frames (1 thru 7)
 FRACK=6000		; Level 2 timout in milliseconds
 RESPTIME=1000		; Level 2 delayed ack timer in milliseconds
 RETRIES=5		; Level 2 maximum retry value
 PACLEN=128		; Default max packet length for this port
 UNPROTO=:		; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
 BCALL=N9LYA		; BTEXT call. unstated defaults to APPL1CALL
 L3ONLY=0		; 1=No user downlink connects on this port
 DIGIFLAG=1		; Digipeat: 0=OFF, 1=ALL, 255=UI Only
 DIGIPORT=0		; Port on which to send digi`d frames (0 = same port)
 USERS=0		; Maximum number of L2 sessions, 0 = no limit
ENDPORT
;
;
;
PORT			; 
 PORTNUM=2		; Optional but sets port number if stated
 ID=OpenNET 223.600 9.6k Backup
 TYPE=ASYNC		; Port is RS232 Com
 PROTOCOL=KISS		; TNC is used in KISS mode
 NOKEEPALIVES=1
 FULLDUP=1		; Only meaningful for KISS devices
 COMPORT=/dev/ttyUSB7 ; # = SERIAL COM PORT 
 SPEED=38400    	; RS232 COM PORT SPEED
 CHANNEL=B		; A for single channel TNC, A or B for multichannel
 PERSIST=64		; PERSIST=256/(# of transmitters-1)
 SLOTTIME=100		; CMSA interval timer in milliseconds
 TXDELAY=250		; Transmit keyup delay in milliseconds
 TXTAIL=0	; TX key down, in milliseconds, at packet end;
 QUALITY=192		; Quality factor applied to node broadcasts heard on
			; this port, unless overridden by a locked route
			; entry. Setting to 0 stops node broadcasts
 MINQUAL=175		; Entries in the nodes table with qualities greater or
			; equal to MINQUAL will be sent on this port. A value
			; of 0 sends everything.
 MAXFRAME=4		; Max outstanding frames (1 thru 7)
 FRACK=2000		; Level 2 timout in milliseconds
 RESPTIME=1000		; Level 2 delayed ack timer in milliseconds
 RETRIES=15		; Level 2 maximum retry value
 PACLEN=64		; Default max packet length for this port
 UNPROTO=Node:		; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
 BCALL=n9lya-7		; BTEXT call. unstated defaults to APPL1CALL
 L3ONLY=0		; 1=No user downlink connects on this port
 DIGIFLAG=1		; Digipeat: 0=OFF, 1=ALL, 255=UI Only
 DIGIPORT=0		; Port on which to send digi`d frames (0 = same port)
 USERS=0		; Maximum number of L2 sessions, 0 = no limit
 NOKEEPALIVES=1
 WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 223600000, PKT9600, 60, 35, 9
 
ENDPORT
;
;
PORT            ; AXIP/UDP Port (Internet Link) 
 PORTNUM=3		; Optional but sets port number if stated
 ID=AX/IP/UDP	(Internet Linking)	; Displayed by PORTS command
 TYPE=EXTERNAL		; Calls an external module
 DRIVER=BPQAXIP		; Uses BPQAXIP.DLL
 QUALITY=192		; Quality factor applied to node broadcasts heard on
			; this port, unless overridden by a locked route
			; entry. Setting to 0 stops node broadcasts
 MINQUAL=168		; Entries in the nodes table with qualities greater or
			; equal to MINQUAL will be sent on this port. A value
			; of 0 sends everything.
 MAXFRAME=5		; Max outstanding frames (1 thru 7)
 FRACK=5000		; Level 2 timout in milliseconds
 RESPTIME=1500		; Level 2 delayed ack timer in milliseconds
 RETRIES=5		; Level 2 maximum retry value
 PACLEN=236		; Max = 236
 NOKEEPALIVES=1
 DIGIFLAG=1
 DIGIPORT=14
 CONFIG			
 UDP 10093
 MHEARD			;Opens AXIP MHEARD window	
 AUTOADDMAP
 BROADCAST NODES
 BROADCAST QST
 MAP W9ABA-7 *.*.*.* udp 10093 B	
 MAP AE5E-14 *.*.*.* UDP 10093 B 
 MAP n0kfq-4 *.*.*.* UDP 10093 B
 MAP N4ZKF-5 *.*.*.* UDP 10093 B
 MAP KQ0I-7 *.*.*.* UDP 10093 B
 MAP VK2DOT *.*.*.* UDP 10093 B
 MAP K7MT *.*.*.* UDP 10093 B
 MAP KB8PMY-5 *.*.*.* UDP 10093 B	
 MAP N9UMJ-7 *.*.*.* UDP 10093 B
 MAP KJ6IX-4 *.*.*.* UDP 10093 B
 
;-----------------------------------------------------------------
;
PORT
 PORTNUM=4
 ID=HF_SkipNET Pactor 746Pro
 TYPE=EXTERNAL
 COMPORT=/dev/ttyUSB10            ; # = SERIAL COM PORT 
 SPEED=57600            ;COM Port Speed
 DLLNAME=SCSPactor.DLL
 QUALITY=0
 INTERLOCK=4            ;Optional - set if you have two ports sharing the same radio.
                        ; Set the same Interlock value on both ports.
 
 CONFIG                 ; Driver-Specific Configuration
 

RIGCONTROL
/dev/746-RC 19200 ICOM IC746 66 
7,3.58700,usb,f1,d,p123,w2
7,14.11100,usb,F1,d,p123,w2
7,18.10800,usb,F1,d,p123,w2
****
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 3587000, P123, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, P123, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, ARDOP1000, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, P12, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, ARDOP500, 50, 50, 6
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 14112500, WINMOR1600, 50, 50, 8
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 18109500, WINMOR500, 50, 50, 6 6
#
# Note that the PTC is sent the RESTART command before being initialised, so only non-default
# parameters need to be set
#
PAC BAUD 300 	; Sets the PTC Packet Modem to Packet Mode
PAC TXD 600
SCANFORROBUSTPACKET 7	; The PTC will listen for HF Packet calls for the first n seconds
#			; of each scan interval, and for Pactor the rest.
PAC MCON 6
PAC MON 6
#
 UseAPPLCallsforPactor
 TONES 4		; Standard Pactor III tones  1500 Hz audio center
 MAXERR 60		; Max retries 
 MODE 2			; ASCII mode, no PTC II compression (Forwarding will use FBB Compression)
 MAXSUM 60		; Max count for memory ARQ
 MAXDOWN 5
 MAXLEVEL 3
 MAXT 2
 MAXUP 3
 CWID 0 2		; CW ID disabled
 ADDLF 0		; Auto Line Feed disabled
 ARX 1			; Amtor Phasing disabled
 AP 100			;
 AQ 1			; Automatic Frequency Parameter
 BELL 1			; Disable Bell
 BC 0			; FEC reception is disabled
 BR 7			; 
 BKCHR 2		; Breakin Char = 2
 CHOBELL 1		; Changeover Bell off
 CMSG 0			; Connect Message Off
 CONT 3
 CWID 0 3 
 CWSPEED 100
 FREE MODE 0
 LFIGNORE 0		; No insertion of Line feed
 LISTEN 1		; Pactor Listen disabled
 LSB
 MAIL 0			; Disable internal mailbox reporting
 MYCALL N9LYA		;
 MYSELC NLYA		;
 REMOTE 0		; Disable remote control
 FSKA 750		;
 PSKA 750		; TX Output level. May need optimising. Default is 140
 STATUS 2		; Automatic Status must be enabled for BPQ32
 PTCHN 31		; Pactor must use Host Mode Chanel 31
 PDUPLEX 1		; PDuplex must be set. The Node code relies on automatic IRS/ISS changeover
 PDTIMER 6		; 5 second duplex timer 
 BUSYHOLD 8		;Busy Detect Augmentation
 BUSYWAIT 12		;
ENDPORT

;
PORT			; 440 9600 Baud 
 PORTNUM=5		; Optional but sets port number if stated
 ID=OpenNET 432.250 9.6k 	TEKK; Displayed by PORTS command
 TYPE=ASYNC		; Port is RS232 Com
 PROTOCOL=KISS		; TNC is used in KISS mode
 NOKEEPALIVES=1
 FULLDUP=0		; Only meaningful for KISS devices
 COMPORT=/dev/ttyUSB8              ; # = SERIAL COM PORT 
 SPEED=19200		; RS232 COM PORT SPEED
 CHANNEL=A		; A for single channel TNC, A or B for multichannel
 PERSIST=64		; PERSIST=256/(# of transmitters-1)
 SLOTTIME=50		; CMSA interval timer in milliseconds
 TXDELAY=150		; Transmit keyup delay in milliseconds
 TXTAIL=100		; TX key down, in milliseconds, at packet end
 QUALITY=192		; Quality factor applied to node broadcasts heard on
			; this port, unless overridden by a locked route
			; entry. Setting to 0 stops node broadcasts
 MINQUAL=175		; Entries in the nodes table with qualities greater or
			; equal to MINQUAL will be sent on this port. A value
			; of 0 sends everything.
 MAXFRAME=2		; Max outstanding frames (1 thru 7)
 FRACK=4000		; Level 2 timout in milliseconds
 RESPTIME=100		; Level 2 delayed ack timer in milliseconds
 RETRIES=15		; Level 2 maximum retry value
 PACLEN=128		; Default max packet length for this port
 UNPROTO=Node:		; BTEXT broadcast addrs format: DEST[,digi1[,digi2]]
 BCALL=N9LYA-8		; BTEXT call. unstated defaults to APPL1CALL
 L3ONLY=0		; 1=No user downlink connects on this port
 DIGIFLAG=1		; Digipeat: 0=OFF, 1=ALL, 255=UI Only
 DIGIPORT=0		; Port on which to send digi`d frames (0 = same port)
 USERS=0		; Maximum number of L2 sessions, 0 = no limit
 WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23, 432250000, PKT9600, 35, 35, 9, 205
ENDPORT
;
PORT
 PORTNUM=6
 ID=Skipnet RPR/HF 706MKIIG;(RPR and HF Packet) ;COM30
 TYPE=EXTERNAL 
 COMPORT=/dev/TrackerN40
 SPEED=38400
 DLLNAME=SCSTRACKER.DLL
 INTERLOCK=6
 CONFIG
  ;APPL BBS
RIGCONTROL
/dev/706-RC 19200 ICOM IC706 58  
7,7.1010,usb,F1,r2,w2
7,7.1030,usb,F1,r2,w2
7,7.1095,lsb,F1,h1,w1
****
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23,  7104500, ROBUST, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23,  7102500, ROBUST, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23,  7102500, WINMOR500, 50, 35, 3
WL2KREPORT PUBLIC, api.winlink.org, 80, K9BBS-10, EM68SR, 00-23,  7102500, ARDOP500, 50, 35, 3
#
  O 4              	; MAXFRAME
  F 190	             	; FRACK
  T 8 			; TX Delay
  DEFAULT ROBUST     	; Default mode is RP
  USEAPPLCALLS      	; Accept connects to all APPLCALLS
  %L 1500      		; Centre Freq for Normal Packet (Default is 1500)
  @I 64			;Paclen = 60
  %T 1          	:TX Autotracking 1 = on
  %N 10
ENDPORT
;
PORT
 PORTNUM=7
 ID=Telnet Server
 Driver=Telnet

CONFIG
 LOGGING=1
 DisconnectOnClose=1
 TCPPORT=8010 
 FBBPORT=8011 8012 8013 8014
 LOGINPROMPT=user:
 PASSWORDPROMPT=password:
 MAXSESSIONS=26 ;was 12
 HTTPPORT=8080
 CMS=1 
 CMSCALL=K9BBS
 CMSPASS=*********
 

  CTEXT=Welcome to K9BBS`s Telnet Server\Enter ? for list of commands

USER=N9LYA,********,N9LYA,"",SYSOP
ENDPORT
;
;
PORT
 PORTNUM=8		; WINMOR port Tracker Pair
 ID=Skipnet WINMOR 706MKIIG 7.101U
 TYPE=EXTERNAL
 PROTOCOL=WINMOR
 DLLNAME=WINMOR.DLL
 INTERLOCK=6
 QUALITY=0

CONFIG			; Winmor config
ADDR 192.168.1.12 18500 PATH REMOTE:C:\WINMORII\WINMOR TNC.EXE
CAPTURE USB audio CODEC-01
PLAYBACK USB audio CODEC-01
CWID FALSE
DEBUGLOG True
BW 1600
DRIVELEVEL 100
MODE AUTO
ROBUST False
SHOW True
BUSYLOCK False
BUSYHOLD 5             
BUSYWAIT 12  
ENDPORT
;
;
PORT
 PORTNUM=9		; WINMOR port Pactor Pair
 ID=Skipnet WINMOR 746Pro 14.111U
 TYPE=EXTERNAL
 PROTOCOL=WINMOR
 DLLNAME=WINMOR.DLL
 INTERLOCK=4
 QUALITY=0

CONFIG			; Winmor config
ADDR 192.168.1.12 18600 PATH REMOTE:C:\WINMOR\WINMOR TNC.EXE
CAPTURE USB audio CODEC-02
PLAYBACK USB audio CODEC-02
CWID FALSE
DEBUGLOG True
BW 1600
DRIVELEVEL 100
MODE AUTO
ROBUST False
SHOW True
BUSYLOCK False
BUSYHOLD 5             
BUSYWAIT 12  
ENDPORT
;
;
PORT
   PORTNUM=10
   ID=OpenNET 223.600 9.6k
   COMPORT=/dev/555;        COM Port Address
   SPEED=38400;       COM Port Speed
   DRIVER=TRKMULTI

   QUALITY=192          ;Setting to 0 stops node broadcasts on this port
   MINQUAL=175
   PACLEN=128         ;Max = 236 if using NETROM links  
   

   CONFIG             ; Driver-Specific Configuration
   M UISC
   PACKETCHANNELS 5   ; Limit to 5 simultaneous connections
   R 0                ; Digipeating OFF
   F 600             ; FRACK: Setting to 3 seconds.
   N 10               ; RETRY: Setting to 10
   O 2                ; MAXFRAME: Setting to 2
   T 35               ; TXDELAY: Setting to 1/2 second (50 * 10)
   @T2 150            ; RESPTIME: Setting interval before ack of received packet to 1.5 seconds.
   %N 5               ; TXTAIL - new TXTAIL (fw 1.5v) setting in 10ms increments.
   ; Comment out the desired speed.
   ;%B 1200            ; 1200 is the poweron default, but setting it anyway.
   %B 9600            ; 9600 
   ;
   %L +500           ; AFSK
   %XA 880           ; Set 300/1200 output amplitude to 3 kHz Peak deviation per measurement.
   %XF 1600           ; Set 9600/19k2 output amplitude to 400 mV PP per ID-880H manual.
   %E 2               ; Set lower tone in 1200 mode (fw 1.5s) to 1/2 voltage 6 dB down from high.
   
ENDPORT   
;
;
PORT
   PORTNUM=11
   ID=OpenNET 145.050 1.2k
   COMPORT=/dev/050;        COM Port Address
   SPEED=38400;       COM Port Speed
   DRIVER=TRKMULTI

   QUALITY=192          ;Setting to 0 stops node broadcasts on this port
   MINQUAL=175
   PACLEN=128         ;Max = 236 if using NETROM links  
   

   CONFIG             ; Driver-Specific Configuration
   M UISC
   PACKETCHANNELS 5   ; Limit to 5 simultaneous connections
   R 0                ; Digipeating OFF
   F 600             ; FRACK: Setting to 3 seconds.
   N 10               ; RETRY: Setting to 10
   O 2                ; MAXFRAME: Setting to 2
   T 35               ; TXDELAY: Setting to 1/2 second (50 * 10)
   @T2 150            ; RESPTIME: Setting interval before ack of received packet to 1.5 seconds.
   %N 5               ; TXTAIL - new TXTAIL (fw 1.5v) setting in 10ms increments.
   ; Comment out the desired speed.
   %B 1200            ; 1200 is the poweron default, but setting it anyway.
   ;%B 9600            ; 9600 
   ;
   %L +500           ; AFSK
   %XA 880           ; Set 300/1200 output amplitude to 3 kHz Peak deviation per measurement.
   %XF 1200           ; Set 9600/19k2 output amplitude to 400 mV PP per ID-880H manual.
   %E 2               ; Set lower tone in 1200 mode (fw 1.5s) to 1/2 voltage 6 dB down from high.
            
ENDPORT  
;
;
PORT
 PORTNUM=12
 ID=Tracker 10.1473 USB ;(RPR APRS) 
 TYPE=EXTERNAL 
 COMPORT=/dev/098
 SPEED=38400
 DLLNAME=SCSTRACKER.DLL
 INTERLOCk=12
 CONFIG
****
#
  O 4              	; MAXFRAME
  F 190	             	; FRACK
  T 8 			; TX Delay
  DEFAULT ROBUST     	; Default mode is RP
  USEAPPLCALLS      	; Accept connects to all APPLCALLS
  %L 1500      		; Centre Freq for Normal Packet (Default is 1500)
  @I 64			;Paclen = 60
  %T 1          	:TX Autotracking 1 = on
  %N 10
ENDPORT
;
;
PORT
 PORTNUM=13
 ID=HF_Skipnet NET105  ;(RPR and HF Packet Pair) 14.105 
 TYPE=EXTERNAL 
 COMPORT=/dev/105;
 SPEED=38400
 DLLNAME=SCSTRACKER.DLL
 INTERLOCK=13
 CONFIG
****
#
  O 4              	; MAXFRAME
  F 700	             	; FRACK
  T 50 			; TX Delay
  DEFAULT HFPACKET     	; Default mode is 300 Baud Packet
  USEAPPLCALLS      	; Accept connects to all APPLCALLS
  %L 1500      		; Centre Freq for Normal Packet (Default is 1500)
  @I 64			;Paclen = 60
  %T 1          	:TX Autotracking 1 = on
  %N 10
ENDPORT
;
;
PORT
PORTNUM=14
ID=HF_Skipnet ARDOP1 706MKIIG
DRIVER=ARDOP 
INTERLOCK=6
CONFIG
ADDR 192.168.1.12 8520 PATH REMOTE:C:\ARDOP1\ARDOP_WIN.EXE 
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0

ENDPORT
;
;
PORT
PORTNUM=15
ID=HF_Skipnet ARDOP1 746Pro
DRIVER=ARDOP 
INTERLOCK=4
CONFIG
ADDR 192.168.1.12 8515 PATH REMOTE:C:\ARDOP2\ARDOP_WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0

ENDPORT
;
;
PORT
PORTNUM=16
ID=HF_Skipnet ARDOP2 746Pro
DRIVER=ARDOP 
INTERLOCK=4
CONFIG
ADDR 192.168.1.12 8522 PATH REMOTE:C:\ARDOP1\ARDOP_2WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0

ENDPORT
;
;
PORT
PORTNUM=17
ID=HF_Skipnet ARDOP2 706MKIIG
DRIVER=ARDOP 
INTERLOCK=6
CONFIG
ADDR 192.168.1.12 8526 PATH REMOTE:C:\ARDOP2\ARDOP_2WIN.EXE
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0

ENDPORT
;
;
PORT
PORTNUM=18
ID=OpenNET ARDOP 147.555 
DRIVER=ARDOP 
INTERLOCK=16
CONFIG
ADDR 127.0.0.1 8517 PATH /home/jerry/ardop/ardopc 8517
CAPTURE USB audio CODEC
PLAYBACK USB audio CODEC
DEBUGLOG TRUE
CMDTRACE TRUE
CWID FALSE
DRIVELEVEL 100
BUSYDET 8
BUSYWAIT 20
GRIDSQUARE EM68SR
FECREPEATS 0

ENDPORT
;
/*
;
 PORT
PORTNUM=19 
ID=FLDigi-1 OpenNET
DRIVER=fldigi
PACLEN=64
INTERLOCK=8
CONFIG
 ADDR 192.168.1.12 7342 PATH REMOTE:C:\FLDIGI\FLDIGI.exe
 TIMEOUT=10
 RETRIES=5
 DEFAULTMODEM MFSK32/1000 ;5XPSK63R/1000
 UPDATEMAP
ENDPORT
;
;
;
 PORT
PORTNUM=20 
ID=FLDigi-2 OpenNET
DRIVER=fldigi
PACLEN=64
INTERLOCK=12
CONFIG
 ADDR 192.168.1.12 7442 PATH REMOTE:C:\FLDIGIII\FLDIGI.exe  
 TIMEOUT=10
 RETRIES=15
 DEFAULTMODEM MFSK32/1500 ;5XPSK63R/1000
 UPDATEMAP
ENDPORT
;
*/
;
PORT
PORTNUM=19 ;loopback
TYPE=INTERNAL
ENDPORT
;
;
ROUTES:			; Locked routes (31 maximum)
;N9PMO-2,1,3,0,0,0,1			
;
; CALLSIGN,QUALITY,PORT[,MAXFRAME,FRACK,PACLEN] 
; The values in [...] if stated override the port defaults.
***			; Denotes end of locked routes
;
APPLICATION 1,BBS,,N9LYA,INBBS,255
APPLICATION 2,RMS,C 7 CMS,K9BBS-10,INRMS,255
APPLICATION 3,CHAT,,K9BBS-14,INCHAT,255
APPLICATION 4,DX,C 3 DXLYA s,N9LYA-6,255
APPLICATION 5,JNOS,C 3 INNOS s,N9LYA-5,255
APPLICATION 6,FBB,C 3 BBSLYA s,n9lya-4,255
APPLICATION 7,URONOD,C 3 IN105 s,N9LYA-7,255
APPLICATION 8,MSYS,C 3 BBSBBS,W9BBS,255

 

Jnos axip link

Setup Jnos axip link

# Attach AXIP to SV1CMG
attach axip cmg 256 44.154.142.2 sv1cmg-6
ifconfig cmg description "AXIP to LAMNOS:SV1CMG-6 Jnos"
ifconfig cmg ax25 maxframe 7
ifconfig cmg ax25 paclen 256
#
at 30 "mbox kick sv1cmg+"
#
arp eaves cmg on
arp poll cmg on
mbox mport cmg on

# sv1cmg
ax25 bc cmg on
ax25 heard cmg
ax25 hport cmg on
ax25 bcport cmg on

netrom  interface       cmg 203 201
netrom  bcpoll          cmg
netrom  bcnodes         cmg
inp     ifaces          cmg

trace cmg 0111

 

iptables allow traceroute / axip / rip protocol

#!/bin/bash
ipt="/sbin/iptables"
$ipt -P INPUT DROP
$ipt -P FORWARD DROP
$ipt -P OUTPUT ACCEPT
# Ampr.org
# Port 520 RIP,Routing protocol
$ipt -A INPUT -p udp --dport 520 -j ACCEPT
# Allow traceroute. Je moet de udp poort 33434 en 33523 niet droppen. Een reject is goed.
# Als je hem dropt wordt een traceroute niet mogelijk
$ipt -A INPUT -p icmp --icmp-type 8 -j ACCEPT
$ipt -A INPUT -p udp --dport 33434:33523 -j REJECT
# Proto 4 = IPv4 encapsulation / Proto 93 = ax.25 / Proto 94 = IPIP
# Hier wordt alles toegelaten van en naar het 44 netwerk.
# Wil je alleen het 44net toelaten
# $ipt –I INPUT –s ACCEPT –s 44.0.0.0/8 –d 44.0.0.0/8
#
$ipt -I INPUT -j ACCEPT -s 44.0.0.0/8 -d 0.0.0.0
$ipt -I INPUT -j ACCEPT -s 0.0.0.0 -d 44.0.0.0/8
$ipt -I FORWARD -j ACCEPT -s 44.0.0.0/8 -d 0.0.0.0/0
$ipt -I FORWARD -j ACCEPT -s 0.0.0.0/0 -d 44.0.0.0/8
$ipt -I INPUT -j ACCEPT --proto 4
$ipt -I INPUT -j ACCEPT --proto 93
$ipt -I INPUT -j ACCEPT --proto 94
$ipt -I FORWARD -j ACCEPT --proto 4
$ipt -I FORWARD -j ACCEPT --proto 94
$ipt -I FORWARD -j ACCEPT --proto 93

 

Xnet axudp link Jnos

The axudp link from xnet to jnos has caused a lot of problems.
But he is up and running … Here the explanation.

In the line “attach axudp xnet 256 192.168.1.112” (jnos) is the secret.
This must therefore “not” refer to the ip address of xnet like you
have indicated in ip.net at myip, but to the IP address of Linux itself.
So the ip address of (for example) eth0

Autoexec.nos (Jnos)

attach tun tun0 1500 0
#
ifconfig tun0 ipaddress 192.168.1.222
ifconfig tun0 netmask 255.255.255.0
ifconfig tun0 mtu 1500

shell ifconfig tun0 192.168.1.221 pointopoint 192.168.1.222 mtu 1500 up
pause 2
shell echo 1 >/proc/sys/net/ipv4/ip_forward
shell /usr/sbin/arp -i eth0 -Ds 192.168.1.222 eth0 pub

attach axudp xnet 256 192.168.1.112 (ip-adres Linux (eth0))
ifconfig xnet description "axip link xnet"

Eth0 (Linux)

eth0      Link encap:Ethernet  HWaddr 00:12:3f:2b:c6:6f
          inet addr:192.168.1.112  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::212:3fff:fe2b:c66f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:7844 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7255 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:885500 (864.7 KiB)  TX bytes:1166950 (1.1 MiB)
          Interrupt:16

Ip.net (xnet)

IP.net
#        File: IP.NET
#       (X)Net IP Address
#
myip 192.168.1.201
subnet 192.168.1.0/24
#
# ARP entry for all received IP Frames
arp add 192.168.1.201 slip sdev6
#
#
# Default route
ipr add default SLIP 192.168.1.201
#
iproute add 192.168.1.0/24 slip 192.168.1.201

Autoboot.net (xnet)

attach IP0 axudp 0 1 192.168.1.222   (Ip-adres van Jnos) 

po 0 acon 1
po 0 baud 9600
po 0 dup 0
po 0 win 7
po 0 quality 0
po 0 name pd2lt
r bc ad 0 pd2lt
r bc ad 0 nodes
ro lo a 0 pd2lt-9 d